By Instruction for Bathtub Installation
By Instruction for Bathtub Installation
Blog Article
Here in the next paragraph yow will discover additional good quality material concerning Tools You Need to Install a New Bathtub .
Setting up a bath tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old tub is readily easily accessible, the project can relocate immediately; if you have to open a wall to remove the old bathtub and also position the new bath tub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the new one. See to it you have certified on your own for the task as well as fit attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is far better to think about employing one before you begin. Chances are you may need an expert plumber to make tube links.
This short article will certainly aid you install a new bath tub in your restroom if you have actually currently acquired a new tub and do not require to transform the setup of your previous supply of water pipes.
Your devices and also product checklist should make up the following:
Preparing for the Setup
To start with, the sustaining frame provided with the bath ought to be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets device to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, activate the taps to drain pipes any type of water staying in the system. The process of eliminating the existing faucets can be rather troublesome because of the limited access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water supply as well as check all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as also check the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, deal with the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the bath tub needs to wait until the bath tub has been used at the very least when as this will resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers remain in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer supplied backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former type ought to be connected to the faucet ends initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, resulting in issues with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to permit the motion experienced when the tub remains in use. The sealant can break rather very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our section about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking the time to browse our piece. Sharing is nice. Helping people is fun. I treasure reading our article about Tools You Need to Install a New Bathtub .
Plumbing woes? Connect. Report this page